Build a fence from corrugated sheets. Do-it-yourself corrugated fence: features of selection and installation

Profiled sheets are widely used in construction. But if previously it was suitable only for industrial and temporary structures, today, thanks to improved qualities appearance, used for decorative cladding, fencing and roofing of private houses.

Building a fence from corrugated sheets is cost-effective, practical and simple. All work can be done with your own hands, the main thing is to choose the right materials and carry out installation in accordance with the standards, then the new fence will be beautiful and durable.

Corrugated sheets are made from sheet steel. Giving it a corrugated shape is carried out by cold rolling. A multi-layer protective coating is applied on both sides, which prevents corrosion and provides the material with an attractive appearance.

Corrugation gives a simple steel sheet rigidity and strength, while maintaining low weight and low thickness - these factors make the profiled sheet easy to work with and a reliable material.

Qualitative characteristics, such as load-bearing capacity and resistance to mechanical stress, directly depend on the characteristics of the corrugation and the initial thickness of the sheet. The finishing coat is no less important.

The higher the profile height and the greater the thickness of the steel, the greater the load the material can withstand. And the quality of the decorative layer determines the service life.

Some profiled sheets are produced without a finishing coating, but the application of base protective layers is a prerequisite, otherwise the material will very quickly lose its properties. The metal is galvanized on both sides, passivated and primed. These coatings protect the steel from the external environment and provide reliable adhesion to the decorative layer.

Advantages and disadvantages

Ease of installation - it is ensured by low weight, simple cutting and fixing;
Wear resistance and strength - service life, depending on the brand and type of protective coating, can vary from 5 to 50 years;
Cost-effective – profiled sheet is one of the most inexpensive building materials, since its production does not require large financial and time costs;
Practicality - the surface is easy to care for, no additional painting is required during operation;
Aesthetics - manufacturers are ready to offer corrugated sheeting in various colors, glossy and matte. The laconic appearance makes this material universal in use for any exterior.

Corrugated sheets are not without their drawbacks. This material is less durable than, for example, concrete, wood or brick. Scratches and dents from impacts may remain on its surface. However, the optimal combination of price, quality and ease of installation has made the profiled sheet very popular among ordinary buyers and professional builders.

Types of corrugated sheets

Depending on the characteristics of the corrugated sheet, the scope of its application is determined. To choose the right material, you need to study the markings on the inside. Sheets manufactured according to GOST are designated by the following letter codes:

Wall is intended for the design of facades and the construction of fences. The load-bearing one is suitable for roofing and floor coverings. Universal has average quality characteristics and can be used for various purposes. Products marked C and CH are suitable for erecting a fence.

After the letters in the code there are numbers: the first is the height of the profile shoulder, the second is the thickness of the steel, the third and fourth are the length and width of the sheet. If the marking has a different appearance, this means that the profiled sheet was produced according to specifications and its quality may differ from the standard.

The corrugated sheet for building a fence must have a thickness of at least 0.5 mm, otherwise the sheet may be deformed. The height of the corrugation is optimally 20 mm. Using a larger profile is impractical, it is inconvenient to use, has a smaller usable area and is more expensive, and a lower shoulder will not work either - it will not provide the required rigidity.

The type and thickness of the protective layer are important indicators of the durability of the material and the ability to withstand atmospheric conditions. The market offers corrugated sheets with various types of coatings, the most common of which are:

When choosing a coating, it is necessary to take into account the climatic features of the region: temperature range and air saturation with salt. Near sea coasts, only products coated with pural and PVDF are applicable. In mid-latitudes, polyester can be used. In the northern regions - frost-resistant plastisol.

DIY fence construction

Building a fence from corrugated sheets is a simple option, however, working with this material has some peculiarities. Failure to comply with installation standards will lead to rapid damage to the appearance and damage to the integrity of the fence. Therefore, first you need to develop a work plan and calculate the required amount of profiled sheets, supports and consumables.

Options for a fence made of corrugated sheets

The main types of fences that can be made from profiled steel sheets are sectional and continuous. For the first type, you will need to first prepare sections of brick or steel pipes large diameter. The advantage of such a fence is that the entire width of the corrugated board is used, so the material consumption is less.

When constructing a continuous fence, the sheets will overlap, so when calculating the required quantity, you need to take into account only usable width.

The useful width of the sheet is always less than the actual width by two waves of corrugation, which will serve as connections in the construction of a solid fence.

The main stages of construction of these types of fencing are the same, so for DIY construction you can use the general scheme; the differences are only in calculating the number of sheets.

Material calculation

In addition to the corrugated sheeting itself, construction will require many more materials; it is best to prepare them in advance in the required volume:

Supports (brick or wooden pillars, metal pipes or a square pipe of at least 60 mm);
Transverse logs (tube square with a wall thickness of no more than 2 mm);
Self-tapping screws;
Exterior paint to match the color of corrugated sheets;
Cement mixture.

To calculate the amount of corrugated sheets, the fence perimeter and height are important. It is optimal to use sheets with a width of 1 to 1.5 meters for fencing; they are easy and quick to work with. To reduce material residues unsuitable for installation, it is best to choose sheets whose length is a multiple of the height of the fence.

Material calculation example

For a two-meter fence, the perimeter of which is 12 meters, you will need 6 sheets of corrugated sheets with a working width of 1 meter. This is 2 full six meter long whips of material. You can immediately purchase them in sliced form for ease of transportation.

The number of supports is also determined by the length of the fence. The racks must be stirred at least every 2.5 meters. Their length should take into account not only the visible part, but also the internal part, since the supports need to be deepened into the ground by 1/3. For a fence 2 meters high, posts with a length of at least 2.7 meters are required.

The length of the transverse logs should be equal to the distance between the pillars. The quantity depends on the height of the fence: at least 2 pieces, if the fence is about 2 meters - 3 pieces, then for every meter in height there is one additional crossbar.

Frame installation

For each rack you need to dig a hole, slightly deeper than the underground part of the support - this is necessary for arranging a gravel cushion. You can dig with a regular shovel or garden auger.

Align the supports in the hole and fill them with cement mortar. If the walls of the well are crumbling, you can strengthen them with a sheet of roofing material. To protect the ground part of the racks from moisture, they must first be primed and painted.

It is necessary to install the transverse logs only after a few days, when the solution has completely dried. There are two ways to fix pipes on racks: welding– provides a strong and immovable connection, and bolts– they are easy to install, but over time the fastening may weaken. You can also decorate the fence with products made using the cold forging method.

Installation of sheets

To install corrugated sheets, you can use special brackets that are installed on racks, or attach them directly to joists, but the second method requires a lot of physical effort and experience. The sheet is fixed using roofing screws, with a colored cap that matches the
the color of the fence, and the rubber gasket.

Sheets cut to size must be leveled vertically and secured with self-tapping screws along the edges and in the center on each of the joists. If the fence is solid, then each subsequent sheet of material is laid on the last wave of the previous one and fastened in the same way. At the end of the work, it is necessary to clean the area from unusable material residues, since the cut edges of the corrugated sheeting are very sharp.

The service life of a fence made from corrugated sheets depends not only on the quality of the latter, but also on the installation technology. Often the fence becomes distorted and becomes loose after just a couple of years; in order to avoid this and build it to last, you need to listen to the opinion of experts and not deviate from the norms and rules:

Cover the ends of the supports and sheets with decorative covers so that the metal does not come into contact with moisture;
Remove the top layer of soil under the fence and concrete a small strip on a slope for water drainage;
Paint with moisture-resistant paint all elements of the fence where there is metal without protective coatings;
Screw in screws only between the waves of corrugated sheeting, and do not tighten them too much, as the protective coating may be damaged and signs of corrosion will appear in this place.

Step-by-step instructions for installing a fence made of corrugated sheets and some important features of the work that you should pay attention to are presented in the video.

Installation of fencing from profiled sheets is an affordable, practical and aesthetic improvement option local area. Many works do not require special knowledge, so you can do them yourself, while additionally saving money on professional installation. If you have the skills to work with a welding machine and a gas drill, then installation “from” to “to” can be done independently.

Click to enlarge

A fence made of corrugated sheets is the most common type of fencing for suburban areas. The fence structure consists of the corrugated sheet itself, supports and joists.

Installing a fence made of corrugated sheets is not very difficult and does not require the use of special equipment or expensive equipment.

Many people are interested: how to properly install a fence from corrugated sheets yourself, without the involvement of specialized teams. This is not difficult to do even for a person without experience; for this you will only need one assistant from your family or friends.

To install a fence made of corrugated sheets you will need:

Profiled sheets intended for installation of fences.
Supports: they can be made from round pipes (easier to hammer in) or pipes with a square cross-section (easier to attach logs to). If you plan to install a combined fence with brick pillars, a pipe will still be installed as the core.
Transverse joists: for their manufacture, rectangular pipes or corners are used.
Self-tapping screws for metal.
Paint for supports and joists.
Crushed stone and gravel for butting.

It will help to carry out calculations on the amount of material.

If you install the structure yourself, then a fence made of corrugated sheets without installation will cost you only the cost of materials.

DIY fence installation

First stage of work– preparation of the territory. It is necessary to mark the pillars. The optimal distance between pillars is 2 meters. If the fence is low - one and a half meters, you can increase the distance to 2.5 meters.

The first pegs are placed in the places where the outer supports and supports of the gate group will stand. Then the places where the fence turns are marked: a peg is also placed there. After this, pegs are installed to mark the locations for installing the remaining supports.

After marking, it is necessary, if possible, to level the area along which the fence line will run and stretch the string between the pegs.

Installation of fence posts

Poles can be installed using several methods. Correct installation a high fence requires the installation of a strip-and-pillar foundation.

A combined fence made of corrugated sheet metal with brick pillars is also installed on such a foundation with a plinth.

Eat different variants installing a fence made of corrugated sheets of the simplest type:

The supports are driven into the ground or screwed in (for round pipes only);
The supports are installed using TISE technology with a concrete shoe;
The pillars are concreted;
The pillars are being backed up.

If you want to make a fence from corrugated sheets with your own hands with a standard height of up to two meters in the middle zone on not heaving soils, the most convenient installation technology is butting. This method will protect the support from the effects of frost heaving.

To install the post, you need to dig a hole with a drill to a depth of one third of the above-ground part of the support. On average it is 0.7-0.8 m for middle zone plus 5 cm for crushed stone cushion.

For higher fences and heaving soils, the depth of the hole can reach one and a half meters. The diameter of the hole should be 10 cm larger than the diameter of the pipe.

5 cm of gravel is poured into the bottom of the hole to create a cushion that blocks the effects of frost heaving forces. The gravel must be soaked with water and compacted thoroughly.
Then the support pipe is installed level. The pipes must be aligned vertically using a plumb line.
Along the edges of the hole, it is filled with gravel and crushed stone, broken bricks or stones, which are also spilled with water and compacted during the installation process. Some people fill the hole two-thirds full with rubble and concrete it on top.

After installing all the pillars, you need to level them in height using a level and, if necessary, hammer them in with a sledgehammer. If the fence is installed for a long time, the pipes can be concreted from the inside to reduce corrosion processes.

When concreting, it is necessary to pierce the poured concrete with a piece of reinforcement to expel all air bubbles.

The gate group posts are installed on strip foundation. Correct installation of a corrugated fence is the key to long service life of the fence.

Log installation technology

Logs can be fastened in two ways: welding or bolted. The welding seam is quite unstable to corrosion processes and requires skill in handling the welding machine.

Bolted connections are more reliable and durable. The logs are attached at a distance of 20 cm from the top of the support and from the ground. After installation, they must be carefully painted.

How to attach a profiled sheet?

The profiled sheet needs to be attached together with an assistant, starting from the gate. Each sheet is placed vertically and attached to the joists with self-tapping screws using an electric screwdriver.

Two self-tapping screws secure the sheet at the edges, and one in the middle on the joist. The next sheet is laid on one wave with an overlap.

Installation and installation: final stage

After installing the corrugated sheet, it is necessary to close the supports on top with plastic plugs. This will prevent water from getting inside the pipe.

If the profiled sheet is raised above the ground even 5-10 cm, small rodents, dogs and rabbits will be able to enter your site and disturb your peace. On the contrary, chickens and other domestic animals may run away from you.

But if the sheet rests on the ground, it will begin to rust. Therefore, after completing the installation of the fence, it makes sense to make a double-sided concrete blind area with a slope along its line. It will protect the corrugated sheet from rusting and rainwater will flow along it further away from the fence. At this point, the installation of the corrugated sheet fence can be considered complete.

If you are interested in installation, you can watch photos and videos of the installation process presented on our website.

Corrugated sheeting is a universal material that is used not only in roofing, but also in the construction of fences. It is reliable, neat in appearance, and does not require finishing.

It’s not difficult to install a fence made of corrugated sheets, so it’s quite possible to do it yourself.

Among the advantages of this design:

Wear resistance. The surface is treated with protective solutions, and the metal is not subject to corrosion.
A light weight. Simplifies transportation and installation. No need to use special equipment.
Assembling the fence does not take much time.
Low price. Self-installation Such a fence will be cheaper than a similar one made of brick or stone.
Perfectly protects the area from noise and dust.
Fireproof and environmentally friendly raw materials.
Does not require periodic maintenance or painting.
Looks beautiful and goes well with other materials.
The material is durable.
Lasts a long time.
To be repaired. A single element can be replaced without harm to the entire structure.

The material also has its disadvantages.

If they are not firmly attached to the joists, the sheets will begin to deform under the influence of strong winds.

If the protective coating is damaged, it is necessary to treat the areas with an anti-corrosion primer, otherwise rust will appear there over time.

Selection of corrugated sheets

The quality of the profiled sheets is a key factor in the durability of the fence.

When calculating the amount of material, take into account the dimensions. Standard width - 1155 mm, working width - 1100 mm. The height is different, so it is selected individually. If necessary, they can cut off sheets of the required parameters for you.

Pole material options

Among the most popular there are 3 types. Let's look at them in more detail.

Brick

Sections made of corrugated sheets combine beautifully with brick or stone supports. However, it is not worth building pillars yourself without experience. This should be done under the clear guidance of a knowledgeable person or call the experts.

Articles on the topic:

Tree

It is also possible to build a country fence on wooden supports.

To do this, take timber or hardwood logs. But before you begin to assemble the frame and install the pillars, the raw materials are treated with antiseptics. The lower part, which will be fixed in the ground, is coated with bitumen mastic.

It is important to remember that wood requires periodic maintenance and has a limited lifespan.

Metal

A strong and reliable fence can be made from metal profiles.

Suitable pipes with the following cross-section:

rectangular;
square;
round.

When choosing the right size material, consider:

soil features;
freezing depth;
wind load.

The minimum diameter of the pipe for support is 50 mm with a wall thickness of 2.5 mm.

On heaving soils, the pole should be properly mounted below the freezing point of the soil. On stable soil, the height of the above-ground and underground parts of the support is taken in a ratio of 2:1.

To install supports under the gate, it is better to buy profile pipes of a larger cross-section - 60 * 60 mm with a wall thickness of 3 mm.

On sites with sharp changes in elevation and swampy areas, pipes are replaced with screw piles.

What to make the frame from

When installing a fence in a dacha, the owners' priority is not only a long service life, but also a minimum cost of construction work.

For permanent fencing in the private sector, owners choose a metal frame; around small areas of land - a wooden one.

Let's look at the nuances of each type of material.

Rolled metal (profile pipe)

In combination with a profiled sheet, this option is the most optimal. The fence will be reliable and resistant to wind loads. Such a frame can be installed on estates on a slope, on uneven terrain.

Welding is used to connect elements. The sheets are screwed to the frame with self-tapping screws or rivets.

Before assembling all metal parts into one structure, it is recommended to treat them with an anti-corrosion primer and paint them.

Wooden (from timber)

An inexpensive option is to install a timber frame. It is a lattice. Logs are fixed across the vertically fixed pillars. This is done using nails, screws or a groove connection.

Wooden construction is inferior in strength and service life to metal, so it is chosen much less frequently.

Installation of gates and wickets

When the covering of the sections is completed, you should begin installing gates and wickets. Reinforced posts with a wall thickness of 3.5 mm or more are chosen for the gates. Garage canopies are welded to them. For logs, pipes with a cross section of 20*40 mm and a wall thickness of 2 mm are used. All connections are made by welding. The locking mechanisms are secured against fixing the sheets.

The optimal type of foundation for this would be a strip foundation.

The deviation must be uniform. Sections are created with the same lifting and lowering heights.

The fence is mounted in two ways:

When the differences in ground level are less than the depth, it will be easier to build a foundation for a fence on a slope. The concrete base of the base is made in the form of steps, the top is parallel to the ground.

Photo gallery of finished fencing

Below are different ways fastening corrugated board to the fence, the most original combinations with other materials.

To create a reliable fence yourself, corrugated board is a universal material and a good choice. The finished structure will perfectly complement the site, protect the yard from curious neighbors, and the variety of colors will allow you to purchase a material that will definitely suit any owner.

The main advantages of a fence made of corrugated sheets are relative cheapness compared to other building materials for fencing, durability provided there are no mechanical damages, and ease of installation. Corrugated sheeting is a corrugated steel sheet with a protective layer, it provides noise and dust insulation, it is fireproof, and combines well with other materials.

A fence made of corrugated sheets, properly installed with your own hands, will last for ten years. The service life of some types of fence reaches 25-35 years, depending on the aggressiveness environment(sea wind, ammonia precipitation from the enterprise, etc.). You can make the height of the fence different, apply different patterns on it, imitating brickwork, stone, wood and others.

Corrugated sheeting for fence

When looking for a suitable corrugated fence, you will find that the difference between them lies in the covering material. The following types of metal profile coating are distinguished:

Polymer coating. Increases the level of protection of corrugated sheets and can be painted at the production stage.
Plastisol. It features a thicker coating layer, which provides protection not only from aggressive environments, but also from mechanical damage. This protective material provides greater durability.

It should be noted that the profiled sheets also differ in thickness. Metal profiles with increased thickness are used in load-bearing structures, and for a fence, a profiled sheet with a minimum thickness is suitable (rib height is about 21 mm, metal thickness is up to 0.5 mm).

While following all the tips listed above, do not forget about the appearance of the fence. You can choose a monotonous color or different patterns.

Construction of a fence made of profiled sheets

To install a fence made of profiled sheet metal poles are used (economical option), or a brick column goes around the pipe (expensive option). The pillars are installed with the same distance (after removing the length of the fence and dividing it into equal sections) or, for example, into sections of 2.5 meters, and one section will be obtained “in fact”.

The pillars are concreted, the concrete is allowed to gain strength (depending on weather conditions), and transverse logs (metal square or rectangular pipes) are installed by welding them to the main vertical pillars.

The last step is the installation of the profiled sheet on the transverse joists using rivets or roofing screws.

General scheme for constructing a simple fence made of corrugated sheets

All installation work can be divided into several stages, which we will consider below.

Marking the fence line.

Immediately at the first stage work in progress marking and transferring data onto a sheet of paper. Calculate the number of segments (spans) following a simple rule for installing a fence made of corrugated sheets - the distance between vertical posts ranges from 2.5 to 3 meters. It is very convenient to “mark” future supports using wooden pegs or pieces of reinforcement.

Concreting metal pillars.

The height of the pillars depends on the planned height of the fence. For fences of a standard height of 2 m, use a concreting depth of 100-110 cm below the soil surface; for higher fences, accordingly, we increase the concreting depth, and for low fences, we lower it.

Having dug a hole. it is necessary to start knitting a skeleton from reinforcement under concrete (will increase the durability of concrete). Next, we prepare the concrete - 1 part cement to 3 parts sand and 4-5 parts crushed stone or slag, water. We fill holes with supports with concrete, having first checked them with a building level on all sides and fixed them so that they do not move during pouring, although specialists always double-check metal pillars with a building level after pouring.

Depending on weather conditions, concrete needs to gain strength within three days (in hot weather, moisten the concrete with water every day, this will give additional strength, and in rain and cold weather, this period must be increased by 1-2 days).

Installation of transverse joists.

The next step is the installation of transverse square or rectangular pipes. This is done using a welding machine by “welding” transverse joists to vertical posts. For a two-meter fence, use two transverse logs. Welding areas should be coated with primer paint to provide protection against corrosion.

Fastening profiled sheets.

The final stage of fence installation is attaching the profiled sheets. The sheets are installed with an “overlap” on the adjacent sheet in one wave. They are attached to the transverse joists using roofing screws. It is also necessary to leave a small gap at the bottom of the sheet - from 5 to 10 cm, in order to allow snow and rainfall not to accumulate and to allow the wind to blow through.

Necessary materials for the fence

Before directly installing the fence, you need to calculate everything necessary materials. The most important material is a profiled metal sheet that fills the main area of the fence.

Specialists in installing a fence from corrugated sheets recommend using a sheet with C18 or C21 coding.
Next, you should stock up on metal poles for vertical installation. These can be square pipes 60*60 or 40*40 mm, or round pipes with the same diameters.

You will also need metal transverse joists (rectangular pipes measuring 40*20 mm) to provide basic rigidity and strength. Profiled sheets will be installed on them.

From tools during execution installation work you will need to use the following:

Shovel and crowbar - for earthworks.
Grinder with cutting disc - for cutting fittings and pipes.
Concrete mixer, buckets – preparing and pouring concrete.
Brushes – for painting metal pipes.
Drill or screwdriver - for attaching a profiled sheet to transverse metal joists.

You will also need a construction level, a roll of rope or twine (for marking), a tape measure, a pencil, gloves and various consumables (cutting discs, electrodes, etc.).

Preparing metal for installation

Durability paint coatings applied to the metal surface depends on the correct preliminary preparation of the metal surface for painting. The service life directly depends on the condition of the metal before painting. Therefore, if metal pipes are lying in a warehouse and are covered with a small layer of corrosion, it is necessary to remove it.

There are two types of metal preparation for painting:

Primary preparation. This preparation is carried out to remove scale, dirt and rust until bare steel remains.
Secondary preparation. Surface preparation leaving organic and metal coatings firmly bonded.

After these preparation steps, it is necessary to degrease (white alcohol, gasoline or acetone) the metal surface to be painted, then apply a primer layer. After the primer coat of paint has dried, apply one or more layers, depending on the aggressiveness of the environment.

After installing the vertical posts and metal cross beams, it is necessary to knock off all the scale and slag from the welding machine, and paint the welding areas in one or more layers.

The procedure for installing supports (pillars)

After all the metal supports are prepared (cut and painted), you need to begin their installation. Let's describe this process step by step:

Marking the territory. We divide it into segments, insert pegs and pull the tourniquet.
Digging holes. Using a shovel and crowbar or with a hand (electric) drill.
Concrete cushion. We fill the bottom of the hole with a cushion of sand and crushed stone, then compact it.
Pole installation. We install the support and align it with a level and plumb line.
Pouring concrete. We pour the concrete solution and fix the post level using boards and auxiliary material.

We accurately install corrugated fence posts, as they ensure the strength and durability of the entire structure. There is no need to rush at this stage, because it is better to spend a little more time now than to fix or even completely redo the fence in a few years.

Installation of metal transverse joists (lintels)

The installation of jumpers is carried out using bolted connections or clamps (a relatively old method) or using a welding machine, which is currently one of the most reliable and fastest methods.

Experts in installing fences of this type recommend attaching the logs at a height of 25-30 cm from the surface of the foundation or ground, and at the same distance from the intended top of the fence. This ensures optimal structural strength.

Advice. If you make fence spans 3 m long, then with a length of transverse logs of 6 m there will be a minimum amount of remnants of the metal tube, since the length of the logs will be enough for just two spans.

Installation of profiled sheets on the skeleton of the structure

After completing the main labor-intensive work, all that remains is to attach the profiled sheet. The easiest way is to fix the sheets to the transverse joists using self-drilling screws (roofing screws). Thanks to the special tip of the self-tapping screw, it drills a threaded hole using a drill or screwdriver.

When screwing in self-tapping screws, it is important to remember:

A loose self-tapping screw will subsequently cause leakage with a trace of corrosion.
A tightly twisted self-tapping screw causes deformation of the profile sheet.
A screw screwed in crookedly violates the integrity of the metal and creates a loose fit of the gasket, which causes corrosion.

A correctly screwed self-tapping screw is considered to be screwed in at an angle of 90 degrees with pressure that does not allow overtightening or deformation. Screw screws into every third wave.

Prices for corrugated fences with installation

The cost of a fence made from a profiled sheet depends on the thickness of the metal, the presence of a colored polymer coating on one or both sides, the length and height of the fence. Also, the price depends on the method of concreting and the foundation under the fence, the presence of additional elements in the structure (gate, gates, brick pillars, etc.).

Here are some of the approximate prices for various types of fences made of corrugated sheets (at a height of 2 m with local concreting of vertical pipes):

A fence made of galvanized corrugated sheets costs about 1,400 rubles per 1 linear meter.
A fence made of profiled sheets with a polymer coating on one side - from 1,600 rubles per 1 linear meter.
A fence made of profiled sheets with polymer coating on both sides - from 1800 rubles per 1 linear meter.

In addition to installing the fence itself, you need to take care of the entrances and entrances to the territory. Prices for some additional installations of related work:

A gate made of corrugated sheets (width up to 100 cm) with handles, a lock and a latch - about 5,000 rubles (manufacturing and installation).
Swing gates (from 3-4 meters) with latches and hinges – 10,000 rubles.
Brick pillars of one and a half bricks - 8000 rubles/pillar.

Despite the fact that you can install the fence yourself, it will take a lot of effort and time, so it is often more profitable to order the installation of the fence from professionals.

We invite you to learn how to make a fence from corrugated sheets with your own hands. This design is highly durable and can last for many years. We will also understand the features of developing drawings, calculating the required amount of materials and the procedure for performing installation work.

Read in the article

Types of corrugated fences and photos of structures

The design of fences may vary. Let's look at each type in more detail.

There are two main types of corrugated fences.

The first option is solid fences. In this case, all load-bearing elements are sewn up with corrugated sheets. They are easy to implement, so many people install them with their own hands. In the photo, a solid fence made of corrugated sheets looks like a solid structure.

The second option is sectional fences. Profiled sheets are installed between the supporting elements. Such designs have a more presentable appearance. Especially – fences made of corrugated sheets with posts. However, their installation is much more expensive than solid ones.

We invite you to look at photos of fences made of corrugated sheets, which you can use as ideas for around your home:

1 of 8

How to make a drawing of a fence from corrugated sheets: important points

Before starting installation work, you should prepare a drawing of a fence made of corrugated sheets, from which it will be clear how to make it and in what place to dig it. When developing a sketch, you should consider and provide for:

the presence and location of an existing fence;
peculiarities ;
fencing dimensions;
plan for the location of support posts. They can be located at a distance of 2 - 3 m. The choice is made depending on the location of the fence. For open areas, you should choose the minimum distance;
dimensions and location of the gate and.

The finished drawing must contain:

the location of the fence on the site, indicating the places where there will be elevation differences;
dimensions of the fence indicating the height and length of individual sections;
position of supports.

The procedure for calculating the materials required for the construction of a profile fence

In order to have everything you need at the construction site and reduce the cost of building a profile fence, you should calculate the required amount of materials. We invite you to get acquainted with detailed instructions, describing the order of calculations.

Foundation materials

Installation of cushions and formwork for strip foundations

A cushion of sand and crushed stone is placed along the entire perimeter prepared for the foundation. Formwork is installed along the future fence. The side walls should be further strengthened to prevent the concrete from spreading after.

Pouring the foundation for installing a fence made of corrugated sheets

The work is performed as follows:

Illustration	Description of action
	To ensure sufficient strength of the formed base, it is necessary to lay the individual elements at the bottom of the trench and connect them together by welding. Supports are installed in the prepared pits. The distance between the corrugated fence posts is checked and their spatial position is controlled using a level.
	Concrete is being poured.
	To give the base an attractive appearance, level the top surface. After the concrete has hardened, we dismantle the formwork - usually after 3 - 5 weeks.

Attaching the log

Most often, the lags are attached to the support pillars by welding. If this option does not suit you for some reason, you can use a special one.

Installation of corrugated board on a fence: video example
Not everyone knows which is best to buy corrugated sheeting for a fence. If you have a choice, you should give preference to a material with a thickness of 0.45 - 0.5 mm. The height of the wave, the characteristics of the protective coating, its color and texture also deserve attention.
Attention! The service life of galvanized material is 20 - 30 years, and for polyester-coated sheets it can reach 50 years.

If you are going to install a fence in an area with low wind load, the best option would be profiled sheets C-8 and C-10. If the wind load in the region is high enough, you should pay attention to C-14, C-15, C-18.
Review of metal profile C-8 OH RAL 9003:

More details on Otzovik: http://otzovik.com/review_4899731.html
Review of the profiled sheet for the fence "StalSoyuz":

More details on Otzovik: https://otzovik.com/review_1334138.html
How much does corrugated sheeting cost for a fence - overview of prices for 1 sheet
In an effort to reduce the cost of material for fencing around your dacha, you should not skimp on its quality. The price for a sheet of corrugated fence depends on its geometric and operational characteristics. The thicker the material, the more expensive it will cost to purchase. The type of protective coating and its thickness also matter. The larger the latter, the longer the material will last, and the more expensive the purchase will be.
If you do not plan to install from corrugated sheets yourself, it will be necessary to find out how high the price per meter of work is. The cost will depend on the design features of the fence being installed. On average, prices start from 500 rubles per meter.
Share in the comments whether you ordered or built a fence from corrugated sheets, and how much the fence cost you.